-
Scott Ensign wrote a new post 12 months ago
Monitor My Watershed: New Release!
The Monitor My Watershed development team is excited to announce the release of Monitor My Watershed V0.18. Performance Enhancements This new […] -
rfenster became a registered member 1 year ago
-
neilh20 replied to the topic Primary powering in cold settings in the forum Infrastructure and Equipment 1 year ago
Well as you can see this thread is almost 3 years old. I haven’t tried anything more than what was mentioned above. Your analysis is solid however its dealing with any current pulses and battery voltage measurement circuit.
-
neilh20 replied to the topic POST monitormywatershed.org in the forum Monitor My Watershed 1 year ago
I’ve had some response from staging.monitormywatershed.org:80
but then it seems to become unreliable.
https://github.com/WikiWatershed/monitor-my-watershed/issues/752
-
oliver replied to the topic Primary powering in cold settings in the forum Infrastructure and Equipment 1 year ago
I’ve also seen similar results when working with long-term outdoor deployments. The low quiescent currents are encouraging, but as you noted, the internal resistance of LiSOCl2 becomes more noticeable as the battery ages, especially under load spikes from sensors or radios. A good-sized supercap buffer really helps smooth that out.
If anyone is c…[Read more]
-
oliver became a registered member 1 year ago
-
cameron.cameron became a registered member 1 year ago
-
Jake Lemon started the topic Verizon LTEbee in the forum Mayfly Data Logger 1 year ago
Has anyone had success using a Verizon SIM with the LTEbee modem? If so, any guidance on how to make that work is welcome.
-
neilh20 started the topic POST monitormywatershed.org in the forum Monitor My Watershed 1 year ago
Hello Just wondering what are the target POST
It seems this simple idea can’t be kept working https://github.com/WikiWatershed/monitor-my-watershed/issues/682
and what is the POST for staging for testing.
What’s not working for me is monitormywatershed.org:80 & staging.monitormywatershed.org:80
It used to sometime ago.
-
Hemanth Narayan Dakshinamurthy started the topic Bypassing SDI-12 library to read 8-bits by using high volume binary command in the forum Other Data Loggers 1 year ago
I’m working with soil moisture sensors and currently using the Acclima TDR-305N, which communicates via the SDI-12 protocol. I’ve successfully interfaced with the sensor using the Arduino SDI-12 library and can retrieve standard measurements without issue.
However, I’m now trying to access the actual TDR waveform using the High Volume Binary Com…[Read more]
-
Flint Riverkeeper became a registered member 1 year ago
-
neilh20 commented on the post, A River Flood Monitoring System for Rapid Deployment 1 year ago
Wow looks fascinating. While the SWaP-C mechanical looks so nice, and it’s the open-source software on opensource readable hardware that can make it so nicely extensible. It’s great to see the Stonefly’s SAMD5 […]
-
Scott Ensign wrote a new post 1 year ago
A River Flood Monitoring System for Rapid Deployment
Download as PDF Photo 1: The ORCA deployed on White Clay Creek at Stroud Water Research Center. Loss of lives and property during river […] -
Vale Giovanetti became a registered member 1 year ago
-
Scott Ensign wrote a new post 1 year ago
Real-Time Monitoring of Pollution Biosentinels
Most of the water monitoring technology discussed on EnviroDIY focuses on physico-chemical parameters like temperature, salinity, turbidity, and […] -
Shannon Hicks replied to the topic MayFly Pin On/Off Communication in the forum Mayfly Data Logger 1 year ago
What is the control board that you’re using between the Mayfly and the pumps? Something with some relays? How is it connected to the Mayfly? Via Grove cables or the 2×10 header pins? Can you post some photos of the setup, or maybe a wiring diagram?
-
Kiersten started the topic MayFly Pin On/Off Communication in the forum Mayfly Data Logger 1 year, 1 month ago
I am using a MayFly to control pumps in a water sampler to pump water for specified timeframes. I have the battery powering the pumps and a converter to power the board.
I have my hardware system set up, and I have checked the voltages and battery and pins throughout the system, with reason to believe that my problem is not because of any wiring.…[Read more]
-
Kiersten became a registered member 1 year, 1 month ago
-
Discovery_Center started the topic Can't Upload Data "This file corresponds to another site." in the forum Monitor My Watershed 1 year, 1 month ago
How am I supposed to format my CSV file to upload my data? I keep getting the same error message
<div class=”mdl-snackbar__text”>”Failed to upload data. This file corresponds to another site.”</div> -
Shannon Hicks replied to the topic Issues with Digi XBee 3 Global Modems in the forum Mayfly Data Logger 1 year, 1 month ago
Did you make the changes to the Mayfly’s solder jumpers and sketch? There’s a discussion about the necessary changes here: https://www.envirodiy.org/topic/digi-ltebee-on-mayfly-v1-x/
- Load More
Welcome to EnviroDIY, a community for do-it-yourself environmental science and monitoring. EnviroDIY is part of WikiWatershed, an initiative of Stroud Water Research Center designed to help people advance knowledge and stewardship of fresh water. New to EnviroDIY? Start here
Activity
