All content on EnviroDIY is licensed as Creative Commons Attribution-ShareAlike 4.0. Hardware designs on EnviroDIY are released under the CERN Open Hardware License 1.2. Alternative licenses are available. Learn about licenses and attribution
Welcome to EnviroDIY, a community for do-it-yourself environmental science and monitoring. EnviroDIY is part of WikiWatershed, an initiative of Stroud Water Research Center designed to help people advance knowledge and stewardship of fresh water. New to EnviroDIY? Start here
Community Activity See all activity
nick replied to the topic Continous HAB monitoring in the forum Mayfly Data Logger 1 year, 8 months ago
Thank you for that info.
I need to tap another hole for the Turner device and was wondering if you have a size recommendation for a drill tap and waterproof cable gland.
Shannon Hicks replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 8 months ago
That’s one of the older, now-discontinued Xbee models. Have you used that module before or is it completely new and unused? We had many of them die after about a year of service. Did you modify the SJ19 solder jumper on the back of the Mayfly to change the bee status pin from the usual Bee pin 12 to Bee pin 13. I see you have it listed cor…[Read more]
TDDCR replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 8 months ago
Hi Shannon. I’m using a Digi XBee modem. We can’t get a hologram account through our agency and we have a contract with Verizon, so we’re using this modem with a Verizon SIM card. We have other stations using a similar setup, though some have the v0.5 Mayfly boards with a modem adapter. I’ve attached a picture of this one that’s been giving me problems.
Shannon Hicks replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 8 months ago
What modem are you using with this setup?
TDDCR started the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 8 months ago
We have some Mayfly stations set up already and I’m trying to launch a new one with the v1.1 board. Everything seems to be working fine except for the fact that it ignores whatever loggingInterval I put in and it just logs every minute. It writes to the SD card and sends the data online.
To test if there was some minor issue with my sketch, I went…[Read more]
TDDCR became a registered member 1 year, 8 months ago
TDDCR
@travisdrurydcr
Shannon Hicks replied to the topic Reading -9999 on all Sensors in the forum Mayfly Data Logger 1 year, 8 months ago
Can you email me at mayfly@envirodiy.org, I have a few other questions about the software libraries and hardware combinations for your setup.
WFUWater replied to the topic Reading -9999 on all Sensors in the forum Mayfly Data Logger 1 year, 8 months ago
Unfortunately, we do not have any other boards. Would it be worth it to purchase a new one? Or is there more troubleshooting we could do with the current setup?
Shannon Hicks replied to the topic Reading -9999 on all Sensors in the forum Mayfly Data Logger 1 year, 8 months ago
Do you happen to have a spare Mayfly board, or any other Arduino-type board that you could run the sketch on?
WFUWater replied to the topic Reading -9999 on all Sensors in the forum Mayfly Data Logger 1 year, 8 months ago
Hi Shannon, thank you again. We were finally able to get a voltmeter and test the connection. There is voltage being applied to the sensors when the channel scanning sketch is running, but the program still says no sensor detected and to check the physical connection. We have tested both sensors. Could there be an issue with continuity?