All content on EnviroDIY is licensed as Creative Commons Attribution-ShareAlike 4.0. Hardware designs on EnviroDIY are released under the CERN Open Hardware License 1.2. Alternative licenses are available. Learn about licenses and attribution
Welcome to EnviroDIY, a community for do-it-yourself environmental science and monitoring. EnviroDIY is part of WikiWatershed, an initiative of Stroud Water Research Center designed to help people advance knowledge and stewardship of fresh water. New to EnviroDIY? Start here
Community Activity See all activity
Justen Dilworth became a registered member 1 year, 3 months ago
Justen Dilworth
@jdilworth
Deborah became a registered member 1 year, 3 months ago
Deborah
@deborahmyers
Shannon Hicks replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 3 months ago
Thanks for the update. We’re looking into it, my guess is there’s a conflict between two libraries that is causing some issues, so we’ll have to dig into it and narrow it down.
TDDCR replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 3 months ago
I wanted to come back to this thread to give an update. I did get this working! I had tried unplugging the modem and even commenting out any code related to the modem, it still would log every minute, so it wasn’t related to that. I had some code from another site that we knew worked, so I tried to use that, but then my version of the Modular…[Read more]
Shannon Hicks replied to the topic Continous HAB monitoring in the forum Mayfly Data Logger 1 year, 3 months ago
There’s information on this page, in Section 6.2 about the holes for the cable glands: https://www.envirodiy.org/knowledge-base/building-an-envirodiy-monitoring-station/
As mentioned on that page, the 1/2″ NPT cable glands require you to drill a 23/32” hole and tap it with a 1/2″ NPT tap. I don’t know what the diameter of the cable for your sens…[Read more]
nick replied to the topic Continous HAB monitoring in the forum Mayfly Data Logger 1 year, 3 months ago
Thank you for that info.
I need to tap another hole for the Turner device and was wondering if you have a size recommendation for a drill tap and waterproof cable gland.
Shannon Hicks replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 3 months ago
That’s one of the older, now-discontinued Xbee models. Have you used that module before or is it completely new and unused? We had many of them die after about a year of service. Did you modify the SJ19 solder jumper on the back of the Mayfly to change the bee status pin from the usual Bee pin 12 to Bee pin 13. I see you have it listed cor…[Read more]
TDDCR replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 4 months ago
Hi Shannon. I’m using a Digi XBee modem. We can’t get a hologram account through our agency and we have a contract with Verizon, so we’re using this modem with a Verizon SIM card. We have other stations using a similar setup, though some have the v0.5 Mayfly boards with a modem adapter. I’ve attached a picture of this one that’s been giving me problems.
Shannon Hicks replied to the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 4 months ago
What modem are you using with this setup?
TDDCR started the topic loggingInterval being ignored on v1.1 board. Logs every minute no matter what. in the forum Mayfly Data Logger 1 year, 4 months ago
We have some Mayfly stations set up already and I’m trying to launch a new one with the v1.1 board. Everything seems to be working fine except for the fact that it ignores whatever loggingInterval I put in and it just logs every minute. It writes to the SD card and sends the data online.
To test if there was some minor issue with my sketch, I went…[Read more]