okamran – EnviroDIY

okamran replied to the topic No address detected for any sensor in the forum Mayfly Data Logger 2 weeks, 3 days ago

kwolfe:

So far I haven’t been able to get the turbidity sensor to show up in b_address_change, but a little while ago I did run the DRWI_SIM7080LTE sketch using the clarivue (before I muddled up my libraries), and the clarivue was recording and sending data over even though, at that time, it ALSO never showed up on b_address_change. So perhaps it…[Read more]

okamran replied to the topic No address detected for any sensor in the forum Mayfly Data Logger 2 weeks, 6 days ago

Thank you! After replacing my current libraries folder with a more recent version from the github, I got the Hydros 21 to show up, but not the Clarivue even after moving the white pin to S1. Also, now when trying to upload DRWI_SIM7080LTE, I’m getting compilation errors like “EnviroDIY_ModularSensors/src/LoggerModem.h:46:10: fatal error:…[Read more]

okamran replied to the topic No address detected for any sensor in the forum Mayfly Data Logger 3 weeks, 6 days ago

Oh also forgot to mention that I’m fairly certain I’ve switched the meter hydros 21 factory address away from 0 in the past.

okamran started the topic No address detected for any sensor in the forum Monitor My Watershed 3 weeks, 6 days ago

<p data-start=”122″ data-end=”380″>I currently have my Mayfly board set up with a Hydros 21 water depth sensor and a ClarityView 10 turbidity sensor. I’ve been trying to use the Arduino data logging sketches to record data and upload it to the monitoring component of our watershed database.</p>
<p data-start=”387″ data-end=”638″>During testing, I…[Read more]

okamran replied to the topic Cannot Connect to Internet with SIM in the forum Mayfly Data Logger 6 months, 3 weeks ago

Actually, I just had my SIM card upside down :/

But I appreciate you responding! Though I will also be starting to use the Mayfly/Hydros 21/Clarivue 10 combination, so I might have to keep in mind that you replaced the Clarivues with Campbells. If I may ask, what issue were you getting with the Clarivue 10s? Was it -9999 values and a bunch of…[Read more]

okamran replied to the topic Could not wake modem for clock sync. in the forum Mayfly Data Logger 6 months, 3 weeks ago

Turns out I did have my sim card upside down! The gray part of the hologram is supposed to be facing upwards, not the white part. Now nothing is broken, except for my pride…

okamran replied to the topic Could not wake modem for clock sync. in the forum Mayfly Data Logger 6 months, 3 weeks ago

I’ve now uninstalled the libraries I had previously and redownloaded them. The only thing I have in there is from v.036.0 from ModularSensors. Still no dice.

okamran replied to the topic Could not wake modem for clock sync. in the forum Mayfly Data Logger 6 months, 3 weeks ago

I tried soldering the SJ16 and SJ17 jumpers on the 1.1 Mayfly, and I’m able to get the Bee power LED to turn on a white color, but the Bee network status LED isn’t showing up (though I am using the SIM7080 LTE Bee which perhaps doesn’t offer status outputs?)

okamran replied to the topic Could not wake modem for clock sync. in the forum Mayfly Data Logger 6 months, 4 weeks ago

Oh and I’m using the libraries from like May 2024. Also what do you mean by “cut corners”? Is this the notch in the SIM card? The pins seem to be pretty fine.

okamran replied to the topic Could not wake modem for clock sync. in the forum Mayfly Data Logger 6 months, 4 weeks ago

Additionally, I have arduino 1.8.19 and it says I have the EnviroDIY Mayfly 1284p on /dev/cu.usbserial-0001. These boards were bought fairly recently. My baud is 57600. I believe I kept most of the pins the same as in the original code. I have my apn set to “hologram”, and the UUIDs are in place and are in the same order as the variables.

// How…

[Read more]

okamran replied to the topic Could not wake modem for clock sync. in the forum Mayfly Data Logger 6 months, 4 weeks ago

On the LTE Bee I see more of a carrot orange light and a flashing blue light. Is that what you mean?

okamran started the topic Could not wake modem for clock sync. in the forum Mayfly Data Logger 6 months, 4 weeks ago

I believe I’ve been following all the steps correctly on making our water sensing station, but I can’t get any data to be sent to MonitorMyWatershed. I have just a Hydros 21 Meter sensor and ClariVue 10 sensor, and both read fine, but the data is only being written to my SD card and not online. The EnviroDIY LTE Bee seems to be situated well, and…[Read more]

okamran replied to the topic Cannot Connect to Internet with SIM in the forum Mayfly Data Logger 6 months, 4 weeks ago

Also having the same issues. My LTExBee has an orange and a flashing blue light which I’m pretty sure is a good sign, but I just get that “Could not wake modem for clock sync” message. I’ve tried running the program at least 10 times by now but to no avail. Also the sync session doesn’t take 2 minutes, usually closer to 30 seconds before sending…[Read more]

@okamran