James_NZ

Haha, that worked! Thanks @mbarney.

@heather just FYI. I have attempted to do this on my work computer with the same result.

Is there somewhere I should log MMW problems? We often struggle with the timeseries viewer – it takes a long time to load. Is this a common problem? I thought perhaps it might be caused by our location (New Zealand).

Just adding to this thread.  I have had this twice.  Tonight I couldn’t find a solution despite trying different browsers and incognito mode.

I agree, it is a bit of a show stopper.

James

Further update. My modular sensors code is logging to MMW flawlessly. I never thought I would see the day! Obviously something worked with Sara’s bypass code:

https://github.com/EnviroDIY/ModularSensors/blob/master/tools/LTExBee_FirstConnectionBypass/LTExBee_FirstConnectionBypass.ino

The only other thing I would like to know is how to code the…[Read more]

And here’s the bypass output. I think this worked! Any idea why, and how I could transfer to my modular sensors code?

James

[6008] Putting XBee into command mode...
[7133] Setting I/O Pins...
ATD81
ATD91
ATD71

ATD51
ATP01
[7227] Setting Sleep Options...
ATSM1
[7245] Setting Other Options...
ATDO0
ATP10
[7284] Making sure airplane mode is…

[Read more]

Hi Sara,

Here’s the output from the carriage return code extension:

[6008] Initializing the XBee...

[6010] ### TinyGSM Version: 0.10.6

[6010] ### TinyGSM Compiled Module:  TinyGsmClientXBee

+++OK
ATAP0
OK
ATGT64
OK
ATCT64
OK
ATWR
OK
ATAC
OK
ATHS
B08
[7272] ### Modem:  Digi XBee3 Cellular LTE-M

ATCN
OK
[7288] Putting XBee into command…

[Read more]

Sigh, so I thought we had this but I’m getting the same result.  My code is below, as well as the serial output.

Any thoughts?

#define TINY_GSM_MODEM_XBEE
#define TINY_GSM_RX_BUFFER 64
#define TINY_GSM_YIELD_MS 2
#define TINY_GSM_DEBUG Serial


#include <Arduino.h>
#include <StreamDebugger.h>
#include <TinyGsmClient.h>

StreamDebugger…

[Read more]

Thanks so much for your help. I will try this tonight when I get home!

Have a wonderful Christmas.

James

Thanks for the prompt reply Sara.  You must love these LTE’s by now!

I have had some feedback from Spark who suggest that they have lots of other SARA R410M devices running on the network.

Sara, does the information below mean anything to you?  I figure that I would construct code using “gsmModem.sendAT(GF(“”)) ” to send these configurations t…[Read more]

Just a further update on above.  The IoT provider thinks that the UBlox needs to be told to register.

He suggested using the AT commands:

AT+CPIN?
AT+CREG?
AT+COPS=?

Am I correct in assuming that the way to do this would be via the code below:

    gsmModem.sendAT(GF("CPIN?"));
    gsmModem.waitResponse(180000L, GF("S"),…

[Read more]

Hi,

I have a similar issue with our Xbee3 LTE.  I have the hardware set up identical to how Letsid has it above. I am using the ‘LTExBee_FirstConnection.ino’ code, with the only amendment being a change of the apn to ‘m2m’ (as required for the Spark network).   The serial output I get from this code (after the initial setup) is: “Signal St…[Read more]

Hi all,

Yes we are using the ADS1115.  The board temperature (DS3231) in the box is plotted in yellow below.

James

Thank you @srgdamiano 🙂

Thank you @shicks.

That set me on the right track.  I think I can figure the rest out from here.

Just to make sure my understanding is correct, the ADS1115 is included in the Mayfly because it provides more voltage resolution than on standard analog pins, i.e. it allows for finer divisions than 0-1023 bits?

Thanks for your help.

James