Community Activity

See all activity

• 

  Shannon Hicks replied to the topic LI-710 Compatibility in the forum Environmental Sensors 4 weeks, 1 days ago

  A Mayfly Data Logger should be able to communicate with a LI-710, but someone would have to write a specific SDI12 library file of commands for that sensor, using the example command info in the manual.  It also looks like it’s a continuously-powered sensor, requiring 0.125mA at 12v, with up to 2A during initial startup.   I assume you’ll be po…[Read more]
• 

  Eric Booth replied to the topic Logging data from Milone eTape in the forum Environmental Sensors 4 weeks, 1 days ago

  Sorry for the delay. I’m planning to use it in an H-flume that has a maximum depth of 0.45 meters. It looks like precision is listed as 0.25 mm but I’m okay with accuracy closer to 2 mm.

  And thanks for the sensor range info. I’ll plan to install the eTape in a probe well attached to the flume that extends below the flume entrance elevation. I…[Read more]
• 

  Adam started the topic LI-710 Compatibility in the forum Environmental Sensors 1 months ago

  I am thinking about buying a LI-710 Evapotranspiration Sensor https://licor.app.boxenterprise.net/s/3uehdcs2tkwhb120zm3l961pauvjhl9d

  I was wondering if I could use a Mayfly as a data logger for it without needing to buy a SDI-12 adaptor

  Thank you, Adam
• 

  Adam became a registered member 1 months ago

  

  Adam

  @aoliphant

  View Profile
• 

  neilh20 replied to the topic Logging data from Milone eTape in the forum Environmental Sensors 1 months ago

  Good to hear. and definitely very interested in use with a flume.  What range of water depth measurement are you looking for and depth accuracy of measurement.

  Typically, because  ADCs are got good around 0.0V and rail – the Sensor range from 0.0 to full range, the Voltage range is from 10%Rail to 90%Rail (eg 0.3V to 3.0V for 3.3VDC rail) and t…[Read more]
• 

  Eric Booth replied to the topic Logging data from Milone eTape in the forum Environmental Sensors 1 months ago

  Thanks for the response, Neil. I’m basing the idea that the sensor is calibrated on the following response from Milone when I asked about the difference between the standard voltage divider setup and the other more expensive (+$45) output modules:

  “<span data-olk-copy-source=”MessageBody”>If you go with the standard voltage divider, each sensor…[Read more]
• 

  neilh20 replied to the topic Logging data from Milone eTape in the forum Environmental Sensors 1 months, 1 weeks ago

  Hi Eric – I’ve purchased and looked at using the eTape.

  I was just wondering what made you think they are “calibrated” – that is the “0.0” markings relates to a defined voltage.  Usually this is shown for a calibrated sensor.  Similarly for a Full Scale relates to a known Voltage.?

  looking at the graphs,  they describe “0-5VDC Linear Re…[Read more]
• 

  neilh20 replied to the topic Abnormal power usage? in the forum Mayfly Data Logger 1 months, 1 weeks ago

  Hello Elliot, gosh too bad for the experience. Its a core issue of how to ensure there is enough power, and then also recover from low power events.  However to be able to get some help its best to post the details of the two systems.  Need to phrase the problem with enough detail that some one else might be able to comment.  Battery size and so…[Read more]
• 

  Eric Booth started the topic Logging data from Milone eTape in the forum Environmental Sensors 1 months, 1 weeks ago

  Hi –

  I am a newbie to the world of Arduino/MayFly and would like to create a system to regularly log the output from a Milone eTape sensor that will be installed on the side of a flume outdoors. This is the sensor: https://milonetech.com/shop/ols/products/xn-standard-etape-assembly-75a-a8ed96

  I have contacted Milone and it sounds like the…[Read more]
• 

  Eric Booth became a registered member 1 months, 1 weeks ago

  

  Eric Booth

  @egbooth

  View Profile
• Load More